Search:

Type: Posts; User: Krampus

Page 1 of 13 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    199

    Williams, AZ (vic Flagstaff) was interesting. ...

    Williams, AZ (vic Flagstaff) was interesting. Could do a run up to the canyon. GC railway is there also.
  2. Thread: Shinko 705

    by Krampus
    Replies
    35
    Views
    1,841

    Compared to Metzeler Z8s in OEM sizes, based on...

    Compared to Metzeler Z8s in OEM sizes, based on mfgr published data, the 705 front in 120/70 is a 4% increase and the 150/70 rear is a 7% increase in rolling circumference. Since NC uses rpm and...
  3. If I lift the front while on the center stand,...

    If I lift the front while on the center stand, which actually takes very little pressure on the back seat, the front of mine always falls to the right. I just assume it is the mass of the brake...
  4. Thread: fork boots

    by Krampus
    Replies
    34
    Views
    7,365

    Good point; agreed. Will not zip tie the bottom.

    Good point; agreed. Will not zip tie the bottom.
  5. Thread: fork boots

    by Krampus
    Replies
    34
    Views
    7,365

    These are a good fit for the 41mm end; zip tie. ...

    These are a good fit for the 41mm end; zip tie. So slightly loose on the bottom; could use the included zip tie to snug it on there, but then again it seems to be staying put for the moment just...
  6. Replies
    4
    Views
    142

    Same experience here. Just had another shipment...

    Same experience here. Just had another shipment from them this week.
  7. Thread: Rally???

    by Krampus
    Replies
    11
    Views
    600

    Perhaps something like a MSTA event? MSTA |...

    Perhaps something like a MSTA event?
    MSTA | Great Riders. Great Roads. Join Us!
  8. No worries. Here's honda's instructions that I...

    No worries. Here's honda's instructions that I used:
    https://cssportal.css-club.net/honda/MCA/contents/20121109165858_9886.pdf
  9. Have to go find the part number..... perhaps...

    Have to go find the part number..... perhaps someone will answer in the meantime. There is a relay and fuse that have to go in to the block behind the access panel in the frunk (left of battery).
  10. Did you install the additional relay and fuse...

    Did you install the additional relay and fuse also?
  11. Replies
    5
    Views
    288

    South Bound Honda Typically, very competitive...

    South Bound Honda

    Typically, very competitive pricing.
  12. Replies
    10
    Views
    571

    Very nice. After some riding time, please to...

    Very nice. After some riding time, please to come back and comment on how much compression & rebound damping you are using (i.e. 3 of 6 clicks/turns out from full hard or such); the Aprilia shock...
  13. Replies
    10
    Views
    485

    It is disturbing to think that 25% of riders...

    It is disturbing to think that 25% of riders might prefer the sound of diarrhea in a truckstop, but I guess it depends on what is being compared; and just a bit less so knowing that it is used as a...
  14. Replies
    12
    Views
    689

    I recently installed a 2014 Tuono shock (Sachs);...

    I recently installed a 2014 Tuono shock (Sachs); likely has the same spring as yours, which is supposedly a 95 N/mm rate. Earlier Tuono shocks (emulsion design) had 105 springs on them. Both are...
  15. Centerstand. Should have had one to start with...

    Centerstand. Should have had one to start with as std equipment.
  16. Thread: Oil leak

    by Krampus
    Replies
    8
    Views
    276

    That's the airbox drain; would typically have...

    That's the airbox drain; would typically have condensate in it if anything. If there's oil in it, something is amiss. The breather hose is at the right side top of the valve cover; the one you have...
  17. Thread: Oil leak

    by Krampus
    Replies
    8
    Views
    276

    That's the very same spot that I get drips if I...

    That's the very same spot that I get drips if I over-lube the chain and it flings all over the back of the motor and output sprocket housing. Might suggest thoroughly cleaning the area and then...
  18. Replies
    7
    Views
    309

    Handling with the design size tire mounted, all...

    Handling with the design size tire mounted, all other things being equal, should be equal to or likely better than; on pavement.
  19. Replies
    4
    Views
    450

    Ah, no. Not a good idea.

    Ah, no. Not a good idea.
  20. Thread: Honda NC700X

    by Krampus
    Replies
    7
    Views
    591

    So a round of identify the optional items, since...

    So a round of identify the optional items, since the two pics are quite different in terms of what is on the machine.
  21. Pray tell, where is the local canyon / really...

    Pray tell, where is the local canyon / really curvy road in NE AL?
  22. Replies
    11
    Views
    502

    No need, and do not waste your funds on de-cat...

    No need, and do not waste your funds on de-cat pipe; useless. Best improvement for the money is always the suspension on this category of machine; almost without exception.
  23. Replies
    15
    Views
    1,360

    Or MC Wheel Repair in Tuscon, which is who I used...

    Or MC Wheel Repair in Tuscon, which is who I used to repair a rather large dent in my front rim. Both seem to quote about the same initial price; both say to send them a pic first.

    mcwheel main...
  24. Replies
    48
    Views
    2,952

    Ah, like your opinions. Got it.

    Ah, like your opinions. Got it.
  25. Replies
    48
    Views
    2,952

    Relevancy to discussion?

    Relevancy to discussion?
Results 1 to 25 of 301
Page 1 of 13 1 2 3 4