Thanks Thanks:  0
Likes Likes:  0
Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: frunk lid accent pieces

  1. #1
    Member
    Bike: 700x
    Join Date
    May 2019
    Location
    san diego
    Posts
    80

    frunk lid accent pieces

    anyone know how thos two black accent pieces on the frunk lid are attached, glue/push pins/grommets etc.? thanks

  2. #2
    Senior Member frunk lid accent pieces dduelin's Avatar
    Bike: NC700XD, ST1300, Elite 80
    Join Date
    Jul 2012
    Location
    North FL USA
    Posts
    3,929
    Screws that come up from the underside. There is an inner lid cover held by 4 screws IIRC. Remove that and the screws securing the accent pieces are exposed.
    Dave

    GL1800
    NC700XD




  3. #3
    Super Moderator frunk lid accent pieces 670cc's Avatar
    Bike: NC700X, GL1800, KLX140G, CRF250L Rally, Ruckus 50
    Join Date
    Aug 2012
    Location
    USA
    Posts
    6,972
    Adding to what dduelin said, the 2012-2015 frunk lid is made of four plastic pieces, along with hardware. There is the outer cover and the inner shell. Remove the screws from the bottom of the inner shell, and separate them. I think there is one screw per trim piece, and the remainder of the trim is snapped into place. You cannot remove the trim pieces without splitting the lid halves.
    Greg
    GWRRA Member
    AMA Life Member
    "Quarter Million Mile Club"

    NanCyX . . . . . . . . . . The 250

  4. #4
    Member
    Bike: 700x
    Join Date
    May 2019
    Location
    san diego
    Posts
    80
    I see, Im thinking of removing them and jury rigging some bed roll straps. Of course I need to purchase a nc first. appreciate the info.

  5. #5
    Member
    Bike: NC700X
    Join Date
    Jul 2017
    Location
    Kutztown, PA
    Posts
    31
    I was going to ask if you were 3D printing something...which I was about to start thinking about doing. With my other projects this year, not sure if I'll get to it or not.

  6. #6
    Senior Member frunk lid accent pieces New Commuter700's Avatar
    Bike: NC700X
    Join Date
    May 2018
    Location
    San Tan Valley, AZ
    Posts
    163
    Quote Originally Posted by 670cc View Post
    Adding to what dduelin said, the 2012-2015 frunk lid is made of four plastic pieces, along with hardware. There is the outer cover and the inner shell. Remove the screws from the bottom of the inner shell, and separate them. I think there is one screw per trim piece, and the remainder of the trim is snapped into place. You cannot remove the trim pieces without splitting the lid halves.
    That lid is made up of 13 unique pieces.


    https://tinkergr.wixsite.com/website

  7. #7
    Member
    Bike: 700x
    Join Date
    May 2019
    Location
    san diego
    Posts
    80
    no 3D printing here, just figure something out that works.

  8. #8
    Member
    Bike: NC700X
    Join Date
    Jul 2017
    Location
    Kutztown, PA
    Posts
    31
    If I'm looking at the diagram correctly, then I think we're only talking about #2 and #3. I like the later models but those don't seem like they'll fit at all. I'd like to have something with a couple holes for straps, but still look nice when I don't have anything on.

  9. #9
    Member
    Bike: 700x
    Join Date
    May 2019
    Location
    san diego
    Posts
    80
    well if the piece is attached with screws, im thinking I could run some cordage thru the screw holes possibly.
    Last edited by kalifornia; 21st May 2019 at 06:28.

  10. #10
    Senior Member
    Bike: 750 XD, FLHTC, Can Am RT
    Join Date
    Feb 2016
    Location
    NoVA
    Posts
    124
    I have a '18 with the Givi bag that fits perfectly. If I had an older model and wanted to mount something similar I would go to the hardware store and buy 4 luggage loops and 8 small nuts, bolts and washers.
    DIY accent. I've done that on the top of a police radio box for my Harley. Sounds weird, looks good.

Similar Threads

  1. LED Accent Lights
    By Lou Wambsganss in forum NC700 Mods
    Replies: 12
    Last Post: 3rd December 2013, 10:21
  2. OEM sidecase accent trim
    By searsboy in forum NC700 Mods
    Replies: 0
    Last Post: 4th July 2013, 10:53
  3. Double sided tape problems with accent panels
    By KW7 in forum NC700 General Discussion
    Replies: 2
    Last Post: 28th May 2013, 06:30
  4. Adding on accent colors or stripes
    By mfb in forum NC700 Mods
    Replies: 11
    Last Post: 23rd May 2013, 15:08

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •